Security Level Request Seed Send Key Typical Purpose Level 1 27 01 27 02 Basic coding / variant coding Level 3 27 03 27 04 Adaptations, injector coding, DPF values, etc. Level 5 27 05 27 06 Reprogramming functions Level 7 27 07 27 08 Extended engineering access...

Preparation: Connect to IC_204 in Vediamo. Go to ECU Identification and write down your Software Block #0 (e.g., 2049021203). You need this number for the Seed/Key calculator. You can use SeedCalc or UnlockECU for this. I personally used the UnlockECU Web version. STEP 1: Read Your Original Bytes (D...

Service manual for V-Engines M276/M278 with 6 and 8 cylinders.  m276-m278-service-training-manual.pdf

I just wanted to make a guide for using SDFlash to update NTG head unit as I found it difficult when searching online how to perform this job.To find out what disc you require and what the latest software is you need to get a copy of the SDFlash folders these can be found online if you look hard eno...

This is the procedure set by Bosch to reset the AdBlue system using Vediamo for CR42/CR43/CR60LS/CR61:SCRCM1. Init Contact2. DJ_Zugriffsberechtigung_Drive3. DL_End_of_Line_Task_Inducementsystem4. ECU reset / Ignition OFF/ON5. Read Faults CodesECU1. Init Contact2. DJ_Entriegelung_9A3. DJ_Entriegelung...

We are interested in line 0210, it comes in 2 types: XX XX 19 00 or XX XX 11 00(FF), each is activated differently. In the original AMG, line 0210 contains the code XX XX FF FF, but this does not work on normal dashboards; there are some glitches, and sometimes the tachometer does not work. In ord...

Vediamo comands 1.3D 14 00 00 1D 99 02 0E 6E 2.3D 14 00 00 1D 99 02 0E CF 3.3D 14 00 00 1D 99 02 6E EF 4.3D 14 00 00 1D 99 02 EC EF 5.3D 14 00 00 1D 99 02 77 EF 6.3D 14 00 00 1D 99 02 67 EF EEPROM 1.001D90: XX XX XX XX XX XX XX XX XX 0E 6E XX XX XX XX XX 2.001D90: XX XX XX XX XX XX XX...

Step 1: Launch DTS Monaco and Connect to the Vehicle Open the DTS Monaco software on your computer. Connect the Mercedes-Benz diagnostic interface (C4, C5, or C6) to the vehicle’s OBD-II port. Select the appropriate vehicle model from the software’s interface. Step 2: Choose Variant Coding M...

Step 1: Open DTS Monaco and Select Variant Coding Mode Connect your laptop to the vehicle using an OBD-II interface and OBD-II cable. Launch DTS Monaco and select Variant Coding Mode. Ensure the system detects your vehicle properly before proceeding. Step 2: Connect to IC213 and Modify Codin...

Step 1: Connect TCM Module Launch Vediamo and connect to the TCM (e.g., VGSNAG2 or VGSNAG3) using the ECU variant VCD_SCN_Variantkodierung. Step 2: Enter Manual Coding Go to Manual Coding section. Step 3: Modify Byte Value Locate Byte E6 and change its value from E6 to F6. This enables the...

Notes Before Coding: Always back up your original ECU data before making any changes. Make sure the DTS Monaco project file matches your ECU version. Perform coding only when the vehicle battery is fully charged or supported by a power supply.   How to Code Pedal Characteristic Curve...

If you want your Mercedes-Benz air conditioner to blow colder air than the factory setting, you can modify the Temperature Offset parameter using DTS Monaco. Below is a clear and safe step-by-step guide to help you perform this Mercedes temperature offset coding effectively. Step 1: Connect the Ve...

What You Need to Prepare Before retrofitting Mercedes W204 Rear LED Tail Lights and performing coding with DAS (Diagnostic Assistance System), make sure you have the following tools ready: A working installation of DAS/Xentry – required to perform variant coding on the Rear SAM. Stable power s...

Step 1: Connect and Load Project Connect the diagnostic interface to the vehicle and laptop. Launch DTS Monaco. Load and select the project: ESP 212 This project controls braking and stability-related functions on the W212. Step 2: Modify Variant Coding Navigate to the Variant Coding...